Based in Pomona, CA. Free on-site estimates across the Pomona Valley. Call (909) 699-1776
Gray and black flake garage floor with wood cabinets, epoxy garage floor in Diamond Bar
Tall view of a gray flake garage floor and storage wall, flake epoxy floor in Diamond Bar
Hillside garages and driveways

Epoxy Flooring Diamond Bar, CA

Garage floors, driveways and pool decks for Diamond Bar homes, from The Country Estates to the tracts off Diamond Bar Boulevard.

  • Flake garages finished in a day
  • Prep for 1960s to 1980s slabs
  • Driveway apron coatings
  • Free estimate in 91765 and 91789

★★★★★ 5-Star Rated · 93 reviews on Google, Facebook, Houzz & more

Free on-site estimate

Tell us about the floor and we will call you back to book a visit.

Or call (909) 699-1776

Projects from$2,600two-car flake garage, installed
Flake install1 daywalk on it the same night
WarrantyLimited lifetimeadhesion warranty, in writing
EstimateFreeon-site, with a moisture test
Diamond Bar pricing

How much epoxy flooring costs in Diamond Bar

Epoxy flooring in Diamond Bar costs $6.50 to $18.50 per square foot, and projects start at $2,600. The most common job, an epoxy garage floor in Diamond Bar with a two-car flake system of up to 400 sq ft, runs $2,600 to $4,000 and takes one day.

We come over from Pomona, which borders Diamond Bar to the northeast along the 57 and the 60. The estimate is free and on site, because hillside garages vary a lot: some sit level, some slope toward a drain, and some have a step down from the house.

Every slab gets diamond grinding, crack repair and a moisture test, and every floor carries a limited lifetime adhesion warranty. Building questions for additions and garage conversions go to the City of Diamond Bar. Coating an existing slab is not a structural change.

White marble look metallic floor in a hallway, metallic epoxy floor in Diamond BarMetallic epoxy floor, Diamond Bar
Systems for Diamond Bar

Floor systems for Diamond Bar garages and rooms

Each card opens the full system page.

1 day

Flake epoxy in Diamond Bar

Best on hillside slabs with hairline cracks and a slope toward the door.

Flake page
3 days

Solid color epoxy in Diamond Bar

A clean floor for home gyms on level, sound slabs.

Solid page
3-4 days

Metallic epoxy in Diamond Bar

A finished look for garage rooms and game rooms on dry concrete.

Metallic page
2-3 days

Quartz & sand finish in Diamond Bar

Grip for steep driveway aprons and drain areas.

Quartz page
Two freeways, one valley

Living at the 57 and 60 junction and what it means for your floors

Diamond Bar sits where the Pomona and Orange freeways meet, with the 10 to the north and the 71 to the east. Diamond Bar Boulevard runs along the valley floor toward Brea Canyon, and homes look down on it from the hills on both sides.

Hillside lots often mean driveways and garage floors slope toward the street. A slope is no problem for a coating, but it changes the texture we pick. On a steep apron, we add more grip to the topcoat so the surface stays safe when wet.

Road dust and brake grit settle on driveways near the 57 and 60. A coated garage floor and apron rinse off with a hose, and the polyaspartic topcoat keeps that grit from staining. Our outdoor concrete coatings page covers aprons in more detail.

Between two faults

Hillsides, faults and what they mean for a slab

Diamond Bar sits between the ends of the Chino Fault and the Whittier Fault, both part of the Elsinore Fault Zone, and most homes are built on graded hillside pads. Over decades, that combination shows up as hairline cracks and the odd settled corner in garage slabs.

A coating cannot stop a slab from moving, and anyone who promises that is overselling. What we can do is fill cracks with a polyurea repair compound, grind them flush, and cover them with a flake broadcast that hides the repair. Cracks that are still active get a flexible filler and a note on your estimate.

Hillside garages also tend to slope toward the door or a floor drain. That slope does not matter to flake, which goes down evenly on an incline. Solid and metallic epoxy show uneven spots more, so we look at the slope before suggesting them.

A planned community

From cattle ranch to master-planned suburb

Diamond Bar takes its name from the diamond-over-a-bar cattle brand Frederic E. Lewis registered in 1918. Transamerica bought the ranch in the 1950s to build one of the country's first master-planned communities, and it oversaw construction through the 1960s. The city incorporated in 1989.

That history means most Diamond Bar garages date from the 1960s through the 1980s. Slabs from that era are dense and hard after decades of curing, which is good for strength and hard on cheap coatings, because nothing bonds to that smooth surface without a proper grind.

Many of those garages hold a car, a gym corner and storage. A gray flake blend hides tire marks and dust, and our epoxy flake flooring page shows the blends. The city spans ZIP 91765 and part of 91789, shared with Walnut.

The flake process in Diamond Bar

Our flake process on a Diamond Bar hillside garage

Here is how the flake process runs on a sloped Diamond Bar garage.

  1. Check slope and cracks

    We note the slope, drains and any active cracks before the grinder starts.

  2. Grind the dense slab

    Decades-old hard concrete needs a coarse diamond to open the surface.

  3. Repair cracks

    Hairline and settlement cracks get polyurea or a flexible filler, then a flush grind.

  4. Clean up dust

    Vacuums pull the dust from the slab and the drain edges.

  5. Apply the base

    The basecoat goes on evenly, following the slope of the floor.

  6. Broadcast chips

    A full broadcast of flake covers the base wall to wall.

  7. Level the chips

    Scrapers knock down raised chips and the floor is vacuumed again.

  8. Seal the floor

    A polyaspartic topcoat seals the floor and resists hot tires.

Around the house

What Diamond Bar homeowners coat

Hillside lots mean driveways and pool decks come up as often as garages.

Garage

Diamond Bar garages

Two- and three-car garages, ground and coated in flake.

Driveway

Diamond Bar driveway aprons

The steep section at the garage door, coated to match the garage.

Outdoor

Diamond Bar pool decks and patios

Slip-resistant, UV-stable coatings for backyard slabs.

Interior

Diamond Bar home gyms

Smooth floors that suit rubber mats and wipe clean.

Owner-occupied hills

Why so many Diamond Bar garages get coated

Diamond Bar is a city of owners: 74.2% of occupied homes are owner occupied, per the 2020 census. The first houses went up in 1959 near the future Pomona Freeway, and the city incorporated on April 18, 1989. That makes many garage slabs here several decades old.

Slabs of that age usually have hairline cracks, oil stains and a worn surface. A diamond grind takes the top layer off, the crew fills the cracks, and a full broadcast flake floor covers the rest. Hillside homes along Diamond Bar Boulevard often have garages with a slope to the door, and we check that slope at the estimate.

If you use the garage as a gym or workshop, solid color epoxy suits a home gym, and flake suits a garage that still parks two cars. Want to see options? Look through our gallery.

Diamond Bar prices

Epoxy floor prices for Diamond Bar homes

Typical two-car garage means up to 400 sq ft. Projects start at $2,600. Business floors are quoted after a free site visit.

SystemPer sq ftTypical two-car garage (up to 400 sq ft)Install time
Flake epoxy$6.50-$10 per sq ft$2,600-$4,0001 day
Solid color epoxy$9.50-$11.50 per sq ft$3,800-$4,6003 days
Metallic epoxy$12.50-$18.50 per sq ft$5,000-$7,4003-4 days
Quartz & sand finish$9-$16.50 per sq ft$3,600-$6,6002-3 days
Grind and seal$6.50-$9 per sq ft$2,600-$3,6001-2 days
Patio, driveway & pool deck coating$8-$12 per sq ft$3,200-$4,8001-2 days
Commercial & industrialQuoted after a free site visitQuoted after a free site visitDepends on size and downtime

Prices and details reviewed November 2026.

Get a Diamond Bar estimate through the contact page or see the full project gallery.

Diamond Bar questions

Questions we hear in Diamond Bar

How much does an epoxy garage floor cost in Diamond Bar?

An epoxy garage floor in Diamond Bar costs $2,600 to $4,000 for a two-car flake floor of up to 400 sq ft, installed in one day. A solid color floor is $3,800 to $4,600 and a metallic floor is $5,000 to $7,400.

Can you coat a sloped hillside garage?

Yes. Flake goes down evenly on a slope and toward a drain, so it is our usual pick for sloped garages. Solid and metallic finishes show unevenness more.

Will cracks come back through the coating?

Repaired, stable cracks stay hidden under flake. Active cracks from slab movement can reappear in any coating, so we use a flexible filler and point them out at the estimate.

Do you coat driveways in Diamond Bar?

Yes. Driveway, patio and pool deck coating runs $8 to $12 per sq ft and takes 1-2 days. Many owners coat the steep apron at the garage door to match the garage.

Is my 1970s slab too old to coat?

No. Older slabs are fully cured and strong. They are smooth and hard, so they need a proper diamond grind, which is part of every job we do.

How long before I can drive on the floor?

You can walk on flake the same evening and drive on it after 24 hours. Plan on 3 days for solid color and 3-4 days for metallic.

Which Diamond Bar ZIP codes do you serve?

We serve all of 91765 and the Diamond Bar part of 91789, plus Walnut, Rowland Heights, Chino Hills and Pomona.

What warranty comes with the floor?

Every floor carries a limited lifetime adhesion warranty on the bond between coating and concrete, with written terms at the estimate.

How old are most garage slabs in Diamond Bar?

Diamond Bar homes went up from 1959 on, so many garage slabs are several decades old. Older slabs usually need crack repair and a moisture test before coating, and both are part of our price.

Can you coat a home gym floor in Diamond Bar?

Yes. A solid color floor suits a garage gym, and it runs $9.50 to $11.50 per sq ft over 3 days. Put rubber mats under heavy racks to spread the load on the topcoat.

Nearby cities

More cities near Diamond Bar

We also coat floors in these neighboring cities.

Free on-site estimate

Ready to see your slab coated?

We measure, test the concrete for moisture and give you a written price before any work starts. Projects start at $2,600.